Manufacture and processing of cold rolled steel - 翻译中...
Cold rolled steel is steel produced by cold rolling. Cold rolling is the further thinning of No.1 steel plate to the desired thickness at room temperature. Compared with hot-rolled steel plate, cold-rolled steel plate thickness is more accurate, and the surface is smooth and beautiful, but also has a variety of superior mechanical properties, especially in terms of processing properties. Because the cold-rolled coil is brittle and hard, it is not suitable for processing, so the cold-rolled steel plate is usually required to be annealed, pickling and surface smoothing before being handed to the customer. The maximum thickness of cold rolling is below 0.1-8.0mm, such as the thickness of most cold-rolled steel plates in factories is below 4.5MM; The minimum thickness and width are determined according to the equipment capacity and market demand of each plant.
Introduction
The difference between cold rolled steel and hot rolled steel is not in the smelting process, but in the rolling temperature, or the rolling end temperature. Cold rolled steel is cold-rolled if the final rolling temperature is lower than the recrystallization temperature of the steel. Hot rolled steel is easy to roll and has high rolling efficiency, but the steel is oxidized under hot rolling conditions, and the surface of the product is dark and gray. Cold rolled steel requires large mill power, low rolling efficiency, and intermediate annealing in order to eliminate work hardening during the rolling process, so the cost is also high, but the surface of cold rolled steel is bright, good quality, and can be directly used to process finished products, so cold rolled steel is widely used.
Processing method
Hot-rolled steel coil is used as raw material, and cold continuous rolling is carried out after pickling to remove the oxide skin, and the finished product is rolled hard coil. Because of the cold hardening caused by continuous cold deformation, the strength and hardness of rolled hard coil increase, and the toughness and plastic index decrease, so the stamping performance will deteriorate, and can only be used for simple deformed parts. Rolled hard coil can be used as raw material in hot dip galvanizing plant, because hot dip galvanizing units are equipped with annealing lines. The rolled hard coil weight is generally 6~13.5 tons, and the steel coil is continuously rolled for hot rolled pickling coil at room temperature. The inner diameter is 610mm.
Entwicklung von Stahl Trommel Industrie in Verschiedenen RegionenApril 10, 2023Japan (JSDA) Ca. 85% von stahl trommeln in die Japanischen markt sind verwendet für chemikalien. Die Japan Stahl Trommel Association (JSDA) nahmen bei TOKYO PACK 2022 ausstellung für die erste zeit zu str...view
Spot Markt Für BöschungJuly 1, 2022Schrott: Auf April 8, die schrott markt preis weiter zu laufen dringend, der durchschnitt preis von schrott stahl in 45 wichtigen märkten in die land war 3030 yuan/tonne, bis 18 yuan/tonne im vergleich mit der letzten tradin bestätigen...view
Arten Von Dichtung Von Trommel Closure1July 1, 2022Die stahl trommel abdichtung ring ist eine art von gummi ring mit kreisförmigen oder rechteckige abschnitt. Die am häufigsten verwendet abdichtung ring abschnitt ist O-typ, so es ist genannt O-typ dicht ring. es ist eine der m...view
Stahl preis steigen! Wie lange kann der Preis steigen?July 1, 2022Nach Kann 1, die inländischen markt weiterhin zu pflegen die rising trend, zeitraum ist synchronisiert nach oben, zeitraum schraube brechen durch die frühe hohe punkt (April 17, 3435 yuan), die höchste erreicht...view
The introduction of drum plug - 翻译中...June 16, 2023The content of product introduction today is the drum plug, which is usually divided into two types: galvanized and coated, with two sizes of 2 inches and 3/4 inches, round in shape, and screwed into ...view